Pack fire, sealing and venting

How to Specify a Battery Pack Fire Shield Test

A useful pack fire shield test specification separates external fire, internal propagation, and vent-jet exposure with distinct boundaries and acceptance criteria. Define the fire scenario, protected-side temperature limit, and system-level pass/fail before fixing shield material and test method.

Published October 24, 20267 min readFor battery pack safety engineer · battery system engineers · cell and module mechanical engineers · thermal safety engineers · high-voltage and electrical insulation engineers · ESS fire and safety engineers · supplier quality engineers · technical sourcing and procurement managers
Converted flame-retardant sealing and vent component for battery pack fire shield testing
Converted flame-retardant sealing and vent component for battery pack fire shield testing

A battery pack fire shield test specification fails when it mixes external fire, internal propagation, and vent-jet exposure into one requirement. Each scenario has a different heat source, boundary condition, and acceptance criterion. Start by defining the fire scenario and exposure boundary, then set the protected-side temperature limit and system-level pass/fail. Only after that should you select shield material and test method.

Separate the Three Fire Scenarios

External fire, internal propagation, and vent-jet exposure are three distinct engineering problems. External fire applies heat from outside the pack, often from a fuel fire or adjacent burning object. Internal propagation starts with a single cell failure and spreads through the module. Vent-jet exposure is a high-velocity flame and gas stream ejected from a failed cell or pack vent. A shield that performs well in one scenario may fail in another because the heat flux, duration, and boundary conditions differ.

A common mistake is to use a small-scale flame rating, such as UL 94 V-0, as evidence for pack-level fire protection. That rating measures a material's tendency to self-extinguish under a small, defined flame, not its ability to protect a cold side under a large, sustained fire. The pack shield test must reproduce the actual exposure: flame temperature, heat flux, duration, and orientation.1

  • External fire: heat source outside the enclosure, often a pool fire or burner array
  • Internal propagation: cell-to-cell thermal runaway within the pack
  • Vent-jet: high-velocity flame and gas from a failed cell or pack vent

Define the Exposure Boundary and Heat Source

The exposure boundary is the interface between the fire and the shield. For external fire, specify whether the shield is directly impinged by flame or exposed to radiant heat only. For internal propagation, the boundary is the cell or module surface that the shield contacts. For vent-jet, the boundary is the impingement area of the jet. The heat source must be defined by temperature, heat flux, and duration. A propane burner array can approximate an external pool fire, but the flame temperature and heat flux profile must match the target scenario.

Do not assume a single test covers all boundaries. A shield that withstands a 100 kW/m² radiant panel for 10 minutes may fail under a 200 kW/m² impinging jet for 30 seconds. Specify the heat source and boundary for each scenario separately.1

  • Flame temperature and heat flux at the shield surface
  • Exposure duration and orientation (horizontal, vertical, underside)
  • Distance from heat source to shield

Set the Protected-Side Temperature Limit

The protected-side temperature limit is the maximum allowable temperature on the side of the shield away from the fire. This limit protects adjacent cells, electronics, or occupants. It must be derived from the thermal limits of the protected components. For example, a cell separator may degrade above 80°C, while an electronic control unit may fail at 120°C. The shield test must measure temperature at the protected surface, not just the hot side.

A common failure is to specify only the hot-side temperature or the shield's own survival. The shield may remain intact but allow enough heat through to damage the protected side. Specify the protected-side temperature limit, the measurement location, and the time at which it is evaluated.2

  • Maximum protected-side temperature (e.g., 80°C, 120°C)
  • Measurement location: shield back face, air gap, or component surface
  • Evaluation time: during exposure, at end of exposure, or after cool-down

Include Seams, Penetrations, and Attachments

A fire shield is only as good as its seams and penetrations. Gaps at edges, fastener holes, and cable pass-throughs can allow flame or hot gas to bypass the shield. The test specimen must include the actual seam configuration, fastener type, and any penetrations. If the shield is adhesively bonded, the adhesive must be tested at the expected fire temperature, not just at room temperature.

Specify the seam overlap, fastener spacing, and any sealant or gasket. The test should include a visual inspection for flame passage through seams and a temperature measurement on the protected side near the seam.3

  • Seam overlap and fastener spacing
  • Adhesive or sealant type and application
  • Penetrations: cables, vents, sensors

Separate Normal Sealing from Emergency Vent Flow

Normal sealing and emergency vent flow are separate functions with separate tests. A seal that keeps out water and dust during normal operation may not survive a high-temperature, high-velocity vent jet. Conversely, a vent that opens to relieve pressure during a thermal runaway may not reseal to maintain environmental protection afterward. Specify the normal-service leak rate and the emergency vent flow rate, pressure, and temperature as separate requirements.4

For vent-jet exposure, the test must reproduce the transient flow, not just the total gas volume. Long passages, sharp turns, small sections, membranes, and screens all affect the jet behavior. The shield or vent component must be tested in its installed configuration with the actual flow path.5

  • Normal-service leak rate (e.g., IP67, IP68)
  • Emergency vent flow rate, pressure, and temperature
  • Post-event resealing or one-time venting

Define System-Level Acceptance Criteria

The shield test is not complete without system-level acceptance criteria. These criteria define what constitutes a pass or fail for the entire pack, not just the shield. For external fire, the criterion may be that no flame penetrates the enclosure for a specified time and the protected-side temperature remains below a limit. For internal propagation, the criterion may be that thermal runaway does not propagate to adjacent modules. For vent-jet, the criterion may be that the jet is directed away from critical components and the enclosure remains intact.

Acceptance criteria must be measurable and tied to the safety goal. Avoid vague statements like 'no fire spread' or 'adequate protection.' Specify the exact temperature, time, and visual inspection criteria.1

  • No flame penetration for X minutes
  • Protected-side temperature below Y°C at Z minutes
  • No propagation to adjacent modules

Document the Test Plan for Drawing Review

A complete fire shield test specification becomes a drawing input. The drawing must show the shield stack-up, seam locations, fastener pattern, and any penetrations. The test plan must reference the drawing revision and specify the exact specimen configuration. This allows the shield supplier to quote the correct material and converting process.3

For a VOLTFEND drawing review, provide the cell format, chemistry, state of charge, drawing, stack-up, gap, compression, voltage, exposure, environment, validation target, and volume information. This allows us to assess feasibility and propose a converted component that meets the test specification.3

  • Drawing with stack-up, seams, and penetrations
  • Test plan with heat source, boundary, and acceptance criteria
  • Material and converting feasibility review

PROJECT CHECKLIST

Inputs to bring into the next review

  • 01Cell format and chemistry (e.g., prismatic NMC, LFP)
  • 02State of charge at test start
  • 03Shield drawing with layer stack-up and thickness
  • 04Gap between shield and protected surface
  • 05Compression or attachment method
  • 06Voltage and electrical insulation requirements
  • 07Fire scenario: external, internal, or vent-jet
  • 08Heat source: temperature, heat flux, duration
  • 09Protected-side temperature limit and measurement location
  • 10Seams, penetrations, and fastener details
  • 11Normal-service sealing requirement (IP rating)
  • 12Emergency vent flow rate, pressure, and temperature
  • 13System-level acceptance criteria
  • 14Validation target (e.g., UL 9540A, internal standard)
  • 15Volume and production timing

ENGINEERING FAQ

Questions teams commonly ask

Can I use a UL 94 V-0 material rating as evidence for a pack fire shield?

No. UL 94 V-0 is a small-scale flammability rating that measures self-extinguishing behavior under a defined flame. It does not predict the protected-side temperature or flame penetration resistance of a pack shield under a large, sustained fire. The pack shield must be tested in its installed configuration with the actual heat source and boundary conditions.1

What is the difference between external fire and internal propagation testing?

External fire testing applies heat from outside the pack, typically a burner array or pool fire, and measures the shield's ability to protect the interior. Internal propagation testing initiates thermal runaway in one cell and measures whether the shield prevents spread to adjacent cells or modules. The heat source, boundary, and acceptance criteria are different.

How do I specify the protected-side temperature limit?

The protected-side temperature limit is the maximum allowable temperature on the side of the shield away from the fire. It must be derived from the thermal limits of the protected components, such as cell separator degradation temperature or electronic control unit failure temperature. Specify the measurement location and evaluation time.2

Do I need to test seams and penetrations separately?

Yes. Seams, fastener holes, and cable pass-throughs can allow flame or hot gas to bypass the shield. The test specimen must include the actual seam configuration, fastener type, and any penetrations. Inspect for flame passage and measure protected-side temperature near the seam.3

Can a normal sealing test substitute for a vent-jet exposure test?

No. Normal sealing and emergency vent flow are separate functions. A seal that passes an IP67 water ingress test may fail under a high-temperature, high-velocity vent jet. Specify the emergency vent flow rate, pressure, and temperature as a separate test with the actual flow path.4, 5

SOURCES

Evidence used in this brief

  1. 1
    Examination of entrainment, combustibility, and heat ...

    sciencedirect.com · Accessed October 24, 2026

  2. 2
  3. 3
    Battery Pack Fire Shields engineering data and screening boundaries

    VOLTFEND Engineering · Accessed October 24, 2026

  4. 4
  5. 5
    抱歉,站点已暂停

    yokeytek.com · Accessed October 24, 2026

APPLY THIS TO YOUR BATTERY

Move from a general principle to a drawing-controlled component.

VOLTFEND reviews the position, material family, construction, geometry and validation boundary before recommending a part.

Start an engineering review